This 4th of July tray is the perfect patriotic craft for you to try this summer. It’s made with red, white, and blue buttons and an epoxy finish for lasting use. Don’t let the epoxy scare you – I’ve included step-by-step instructions!

It is that time of year when I love adding patriotic decor to my home. I originally made this button 4th of July tray over on Crafts Unleashed by Consumer Crafts (RIP!).

But y’all, I am still in love with this one today. Grab your supplies and get started on your own version soon! This patriotic tray will be perfect for any 4th of July or summer party you are planning.

Use your button flag tray to serve up drinks or snacks at your party. Or just display it with your other patriotic decor. You will love this one for years, just like I do!

Make This: Button Flag Tray Pinterest image.

Table of Contents

How to Make a Button 4th of July Tray

Making this button tray takes a bit of patience (thanks, epoxy), but the results are so worth it! And don’t worry, I’ll help you every step of the way.

Supplies Needed

Here’s everything you’ll need to gather for this patriotic tray:

Unfinished wood tray
Bright red paint (I used the one pictured below from DecoArt)
Assorted red, white & blue buttons
Hot glue gun & hot glue sticks
Silver sticker
EasyCast clear epoxy
Lighter
Wax paper
Disposable plastic mixing cups (at least two – ones with measurements on the side work best)
Stir sticks (large wooden craft sticks work great)
Craft knife

Button 4th of July Tray Instructions

Ready to get crafting? Here’s how to make my patriotic button tray.

Step 1: Paint your Tray Red

First up, paint your wood tray red with a few coats of paint and allow it to dry.

Red, white and blue buttons on a wood serving tray.

Step 2: Add Buttons

Then, start laying out your buttons in a flag-like pattern. Get your pattern set before you start adding any glue.

Gluing your buttons will take a while. Lift each one and add a small drop of hot glue. Glue into place and move to the next one.

Making a patriotic tray for parties and decor.

Repeat until you have a button flag at the bottom of your tray.

Step 3: Finishing Touches

Glue the silver star right on top of the center of the blue button section of your button tray.

You might also have a ton of hot glue strings on your project. Just use a hair dryer to remove those before continuing.

Step 4: Set with Epoxy

Place wax paper under your 4th of July tray.

Now, it is time for epoxy. Don’t be scared. This is simple, and I am going to show you how. The most critical part is following the directions in the package. Here are a few tips and tricks:

You need an exact 1 to 1 ratio, so measure each part first in your disposable measuring cups.
Protect your work surface with wax paper, and wear gloves to protect your hands. Have plenty of rags on hand as well.
Pour the two parts together and mix with craft sticks. Again, these are disposable.
Follow the mixing instructions exactly. So if it says mix for 2 full minutes – do so.
When pouring, spread out as much as possible, and be sure to get all areas, even the corners.

Step 5: Clean up the Epoxy

After you pour your epoxy, your 4th of July decor tray will look a little like the image below. Boy, all of those bubbles sure do mess things up, right? The epoxy is formulated so that those bubbles will rise up to the top.

Now, it is time to pop them.

Wave a lighter over the surface, being cautious not to actually touch the epoxy. As the bubble heats, it will pop, and you will be left with a smooth surface.

Using a lighter to get bubbles out of 4th of july tray.

Use a craft stick to pop any bubbles around the edges. You will have to repeat this process several times during the first 30 minutes or so of drying time.

Now, not every craft project is perfect, y’all – and I learned a little something during this one. Always protect your work surface, as sometimes you look down and realize that your tray has small holes in the corners, apparently.

I used a rag to clean up several times and changed my wax paper once. Eventually, the epoxy stopped coming out, and all was fine. The next morning, I did have two corners that looked a little like the one below.

Epoxy overflow on 4th of july craft project.

Just use a craft knife to cut away that excess, and your project is done. Be sure to allow the epoxy to cure a full 24 hours before using it.

You can use this method to make a small or large tray. Either will look seasonal and cute!

FAQs

Need help with your 4th of July tray? I’m at your service! If you have any more questions, please leave them for me in the comments below.

Is this button tray food-safe?

This button tray can be food-safe, depending on the epoxy coating you choose to use; the one I linked in the materials is safe to use!

Always check the packaging for food-safe certification before using it to serve food.

How should I use this tray?

This button 4th of July tray is perfect for serving up snacks like chips and dip or a delicious charcuterie spread!

You can also use this tray decoratively on a coffee table, ottoman, or side table. Dress it up with other festive touches like blue star table accents and a patriotic mason jar centerpiece.

How can I use this tray year-round?

While this tray could definitely be used all year, some of us prefer to decorate seasonally. Lucky you – this project is customizable based on the colors and motifs of your choice.

Simply swap out your paint color and buttons for your favorite color or a classic neutral that can be dressed up throughout the year.

More Craft Ideas

I have SO many fun craft ideas for you to try. Beyond my 4th of July tray, these are some of my favorite patriotic projects:

A DIY 4th of July themed decorative tray.

Make this button flag tray for summer parties and decor. Click to see the tutorial for making this!

Total Time 1

Button 4th of July Tray

This 4th of July Tray is the perfect patriotic craft for you to try this summer. It’s made with red, white, and blue buttons and an epoxy finish for lasting use. Don’t let the epoxy scare you – I’ve included step-by-step instructions!

Equipment

Lighter
Disposable mixing cups
Stir Sticks
Craft knife
Hot glue gun

Supplies

1 Wooden serving tray
Bright red paint
Assorted red, white, and blue buttons
Silver star sticker
EasyCast clear epoxy

Instructions

Paint your wood tray red with a few coats of paint and allow it to dry.
Then, start laying out your buttons in a flag-like pattern. Get your pattern set before you start adding any glue.
Lift each button, adding a small dab of hot glue. Glue into place and move to the next one. Repeat until you have a button flag at the bottom of your tray.
Glue on the silver star to your button tray.
You might also have a ton of hot glue strings on your project. Just use a hair dryer to remove those before continuing.
Place wax paper under your tray. Mix and pour epoxy over the tray, following the instructions on the box.
Wave a lighter over the surface being cautious not to actually touch the epoxy. As the bubble heats, it will pop and you will be left with a smooth surface.
Use a craft stick to pop any bubbles around the edges. You will have to repeat this process several times during the first 30 minutes or so of drying time.
Use a craft knife to cut away any excess epoxy that has seeped from the sides.

Tried this project?tag us to show off your work!